Dura-Vent PelletVent Pro
|
This great new product was designed with the installer in mind. The precise fit of twist-lock connections is fast, secure, and leak resistant; and, PelletVent Pro requires only 1" clearance to combustibles. FEATURES:
Twist-lock connections and Open-ended Tee Supports(> shown above left of center bottom in picture) make disconnects easy for periodic cleaning. The Horizontal Vent Cap (>shown center bottom in picture) is for through the wall installations, it also diverts wind and overcomes wind-related problems. It adds a total length of 7 7/16" to the end of your horizontal installation. The Vertical Vent Cap (> shown above in right lower corner of picture) is used to finish vertical installations and twist-locks to the pellet vent providing easy disconnects during cleaning. The Increaser (>shown left of Vertical Vent Cap in picture above) allows you to increase the vent size from 3" to 4" diameter. You'll love the Pellet Vent Tee with Clean-out Adaptor, see full feature below. Installation and components used are also the same for Security Double-Wall Black Stovepipe. Use diagrams below for DuraVent Pellet Vent Pro
*We will contact you after you order with the exact shipping cost to ship to your area. Click here for shipping disclaimer.
Scroll down to view our Ceiling Supports, House Shield, Increasers/Reducers, Flex/Pellet Vent Adaptors, PelletVent to Dura-Vent Chimney Adaptor, PelletVent Wall Thimble, Dura-Vent PelletVent 4" Tee With 3" Take-Off and PelletVent Tee With Clean-Out Adaptor that may be need with your application.
Use the Ceiling Support /Firestop Spacer, at right in picture, when passing through a floor. Includes a Support Clamp.
Appliance Adaptor Increaser
Flex and PelletVent Pro Adaptors
The adaptor on right, in picture, joins DuraVent PelletVent on bottom to RoundFlex or Pro or UltraPro on top.
Provides a "male-end-down" connection.
PelletVent Pro to DuraVent Chimney Adaptor
You must use a Close Clearance Adaptor between this adaptor and a DuraTech Ceiling Support. You must use a Close Clearance Adaptor between this adaptor and a DuraPlus Ceiling Support. Use the Close Clearance Connector when adapting Pellet Vent using a DuraPlus Wall Thimble. Use a Finishing Collar and Close Clearance Adaptor when connecting this adaptor to DuraTech in a Wall Thimble installation.
The black portion attaches to the interior wall to give a nice finished look, and the galvanized section attaches to the exterior wall.
PelletVent Pro 4" Tee with 3" Take-Off
Includes Clean-out Adaptor (Tee cover).
PelletVent Pro Tee With Clean-Out Adaptor
Use this Tee when the appliance has a flue collar on the back.
Order Storm Collar separately.
*We will contact you after you order with the exact shipping cost to ship to your area. Click here for shipping disclaimer. |
PelletVent Pro from Simpson is a
revolutionary patent pending concept FOR
VENTING BOTH PELLET AND CORN-BURNING STOVES AND INSERTS!
It requires no gaskets or sealants to achieve leak-resistant
connections. PelletVent Pro's perfect fit and finish is made
possible with laser-welded 304 stainless steel inner walls and
Zincalume outer walls which results in a clean, steamline
appearance. Offers Limited Lifetime
Warranty.
The Cathedral Ceiling Support Box, on left in
picture, is used for flat or cathedral ceilings. It's 14" tall
and includes a Support Clamp and Trim Collar.
The House Shield includes stand-offs that allow air
circulation which provides protection from blower discharge in
horizontal venting situations. It's used with the 
This product will make it easy
to connect 4" pipe to 3" appliance take-off. Available in
Stainless and Black. 
This product will
make it easy to change from a woodstove pipe to a pellet stove
without changing the entire venting system. Make of 304-alloy
stainless steel, with two female ends, sizes 6" - 4" and 6" -
3". 
The adaptor on left, in picture, is for joining
3" or 4" HomeSaver RoundFlex or Pro or UltraPro on bottom to
Dura-Vent PelletVent Pro on top. 
This Pipe Adaptor can be used for horizontal or
vertical installations, Use it when you need to make a connection to
the flue collar on the pellet appliance.
This adaptor allows you to make a transition from PelletVent to a DuraPlus or DuraTech Chimney
installation. (Also connects to single wall black
stovepipe)
For a horizontal
through-the-wall installation, here's the thimble to use. This
PelletVent Pro Wall Thimble is
designed to fit between standard wall studs; it accommodates a
maximum wall thickness of 7". You'll need a 7 1/2" X 7 1/2"
square hole.
This Tee is perfect for those times when you need
to connect 4" PelletVent to a 3" PelletVent Pipe Adaptor for a
3" pellet outlet. It's 11 1/2" long with a 3" long
take-off to bottom edge of Tee. 
The 3" diameter Tee with Clean-out Adaptor (tee cover) is 11
3/4" tall, and the 4" diameter Tee is 12 5/8" tall. The
distance from the center of the take-off to the bottom of the
Clean-out Adaptor is 7 1/8" for the 3" Tee and 7 1/2" for the 4"
Tee. 
Adjustable Roof Flashing accommodates roof pitches from
0/12" to 6/12" and secures to the roof with silicone sealant and
roofing nails. 
