Single and Multi-Flue Reversible Chimney Caps

Tapcon Masonry fasteners come with these caps and adhesive for mounting. The anchoring flange at the base of the Multi-Flue chimney cap can face either in or out, on any side to give a great fit.  Baffles are available (order separately) for both Stainless Steel and Black Caps. 

*Note: When covering two or more flues sometimes a smoke-over problem occurs (smoke from one flue going down another). A baffle between the flues usually eliminates this when is does occur.

Gelco Galvanized Multi-Flue Chimney Top

(8" Screen Height, 3/4" Mesh)

Each top features a 24-ga. lid and 8" high, 18-ga. 3/4" mesh screen.  Masonry fasteners and mounting adhesive are included.  Gelco's galvanized multi-flue chimney top is quality constructed with full-resistance welds, a One-Piece Screen, and a special cross break in the lid for added strength.  It comes with seven year workmanship and materials warranty and a three-year warranty against rust-through.

*Note:  If the flue tiles extend more than 3" above the chimney crown, use the Knock-Down Model shown below with 12" or 16" screen heights.

Gelco Galvanized Knock-Down Multi-Flue Chimney Top

(12 & 16" Screen Height, 3/4" Mesh)

These galvanized multi-flue tops are economical knock-down models.  They are available in heights of 8", 12, of 16".  When the flue tiles extend more than 3" above the chimney crown, you'll want the 12" or 16" height to ensure proper draft.  Gelco's unique painting system gives their galvanized tops a beautiful, low-luster, high-temperature, black enamel-like finish. They carry a seven-year workmanship and materials warranty and a three-year warranty against rust-through.  Assembly is easy.  Assemble the screen with the drop-in hinge pins and the lid mounts with either four cap screws and washers or four wing nuts, both included.  Gelco has placed weld nuts in the top mounting strips to eliminate stripped threads.  Masonry fasteners and mounting adhesive are included with each top.

BLACK *REVERSIBLE*  Single or Multi-Flue CHIMNEY CAPS  (5/8" Mesh FOR CALIFORNIA)  10" Screen Height

 Same product description as Black Reversible 3/4" above; except these caps are 5/8" Mesh

Gelco Black Galvanized One-Piece Screen Multi-Flue Chimney Top  (5/8" Mesh FOR CALIFORNIA)  8" Screen Height

 Black cap is the one on top in the picture.  These are the same Gelco Multi-Flue Chimney Tops but with 5/8" mesh.  We stock these in the most-used multi-flue sizes - both stainless steel (shown below) and galvanized steel painted black.

Gelco Stainless Chimney Protector (3/4" Mesh) 10 & 12" Screen Height

This cap has a name that means something to the homeowner.  the Chimney Protector does just what its name suggests:  it protects the homeowners' chimney.  And it's backed by Gelco's great, no-nonsense lifetime warranty.  But what really places this cap head and shoulders above the rest is the engineering.  It incorporates all the great features chimney professionals, like you, have asked for over the years.  These feature are what make it the most popular cap in the industry.  Check it out..

SWINGTAB REVERSIBLE MOUNTING STRIPS  The unique design of the SwingTab allows you to simply swing the mounting strips in or out as needed for the best fit.  No tools, no bolts, no awkward panels to assemble and reassemble.  What could be easier?

WING NUTS OR CAP SCREWS, YOUR CHOICE  Just like with our other multi-flue tops, the Chimney Protector lid attaches with either wing nuts or cap screws.  We give you hardware for both options.  With the wing nuts, you don't even need a tool.  Or, use a nut driver and snug it down with bolts.  Either way, it's quick, easy and secure as a lid can be.  All caps come with masonry fasteners and adhesive for mounting onto the crown.

Choose from 13 available sizes, with 10" high mesh, or choose form three sizes with 12" high mesh.

PRODUCT NOTE: All sizes are UL Listed as part of a relining system with HomeSaver Pro and UltraPro, RoundFlex, Rectangle-Flex and OvalFlex.

Chim Cap Stainless Knock-Down Multi-Flue Forever Cap

Here's another great cap for multiple, odd sized, or unlined flues.  It's the stainless steel multi-flue Forever Cap from Chim Cap.  A sturdy, 304 stainless steel construction, lifetime warranty and a five-piece knock-down design.  The 24 ga. lid is removable for easy cleaning.  This cap has a10: high screen with 3/4" oval mesh.  Two sizes are available - 17" x 29" and 17" x 41".  Ordering Note: Tapcon Masonry fasteners and mounting adhesive do not come with these caps.  They must be purchased separately.

Stainless Steel *REVERSIBLE*  Single or Multi-Flue CHIMNEY CAPS  (3/4" Mesh)  10 & 12" Screen Height

These caps are for single flue just as well as multi-flue.  When you have a flue that is an odd size, find a reversible cap that is just a little larger and you just drill a few holes and screw it down into the cement crown and it covers nicely.  Just unscrew the wing nuts on top to remove lid for cleaning.

Tapcon Masonry fasteners come with these caps and adhesive for mounting. The anchoring flange at the base of the Multi-Flue chimney cap can face either in or out, on any side to give a great fit.  Baffles are available (order separately) in Stainless Steel to use with these Caps. 

*Note: When covering two or more flues sometimes a smoke-over problem occurs (smoke from one flue going down another). A baffle between the flues usually eliminates this when is does occur.

Gelco Stainless Steel One-Piece Screen Multi-Flue Chimney Top  (3/4" Mesh)  8" Screen Height

Use these multi-flue chimney tops for multiple, odd-sized, or unlined flues.  Even single flues deserve the protection these tops offer by covering the entire chimney crown.  Strip-proof weld nuts give you a choice - bolt the lid down, or fasten with wing nuts.  Both cap screws and wing nuts are included.  Tops are constructed of 304 stainless steel, have a screen height of 8" with 3/4" mesh, and come with a lifetime warranty.  Masonry fasteners and mounting adhesive are included with each top.

*Note: If the flue tiles extend more than 3" above the chimney crown, use the knock-down model with 12" or 16" screen heights.  Or use the Chimney Protector with 10" or 12" high screen.

Gelco Stainless Knock-Down Multi-Flue Chimney Top (3/4" Mesh)  12 & 16" Screen Height

Gelco Stainless Knock-Down Multi-Flue Tops may be used as a UL Listed termination cap for HomeSaver liners.  When the flue tile extends more than 3" above the chimney crown, you'll want 12" or 16" height to ensure proper draft.  Assembly is easy - two drop-in hinge pins assemble the screen, and the lid mounts with either Strip-proof weld nuts give you a choice - bolt the lid down, or fasten with wing nuts.  Both cap screws and wing nuts are included along with adhesive for mounting. 

Stainless Steel *REVERSIBLE*  Single or Multi-Flue CHIMNEY CAPS  (5/8" Mesh FOR CALIFORNIA) 10" Screen Height

 Same product description as Stainless Steel Reversible 3/4" above; except these caps are 5/8" Mesh

Gelco Stainless Steel One-Piece Screen Multi-Flue Chimney Top  (5/8" Mesh FOR CALIFORNIA)  8" Screen Height

 Stainless Steel Cap in shown on bottom in picture.  These are the same Gelco Multi-Flue Chimney Tops but with 5/8" mesh.  We stock these in the most-used multi-flue sizes - both stainless steel and galvanized steel painted black (shown above).

COPPER *REVERSIBLE* Single or Multi-Flue CHIMNEY CAPS (3/4" Mesh) 10 & 12" Screen Height

These caps are for single flue just as well as multi-flue.  When you have a flue that is an odd size, find a reversible cap that is just a little larger and you just drill a few holes and screw it down into the cement crown and it covers nicely.  Just unscrew the wing nuts on top to remove lid for cleaning.

Tapcon Masonry fasteners come with these caps and adhesive for mounting. The anchoring flange at the base of the Multi-Flue chimney cap can face either in or out, on any side to give a great fit.  Baffles are available (order separately) for Stainless Steel to use with these Caps. 

*Note: When covering two or more flues sometimes a smoke-over problem occurs (smoke from one flue going down another). A baffle between the flues usually eliminates this when is does occur.

Gelco Copper One-Piece Screen Multi-Flue Chimney Top  (3/4" Mesh)  8" Screen Height

For those who want the top-of-the-line traditional chimney caps, we off the Gelco Copper Chimney cap. It has a beautiful color when new, it acquires a rich patina as it weathers, and it adds the much desired Statue of Liberty green as it ages.

The multi-flue copper chimney top is available in four sizes listed below.  The multi-flue tops are made entirely of copper, except for the screws and base which are copper-plated stainless steel.  The 8" high screen is 18-ga. copper and the lid is plated stainless steel.  Tapcon masonry screws and adhesive are included.  These caps come with a lifetime warranty.

PLEASE NOTE: Not recommended for installation on white chimneys - may cause yellow streaks.

COPPER *REVERSIBLE*  Single or Multi-Flue CHIMNEY CAPS  (5/8" Mesh FOR CALIFORNIA)

 Same product description as Copper Reversible 3/4" above; except these caps are 5/8" Mesh