HomeSaver OvalFlex 304-Alloy Stainless
|
With HomeSaver's 4 3/4" wide OvalFlex you don't have to tear out damper frames when relining most flues.. Just run the OvalFlex through the damper, hook up the appropriate adaptors, boots and hardware pieces, and you're done. In a nutshell, it's modular. The whole system of OvalFlex, RectangleFlex, RoundFlex and adaptors, insert boots, and hardware pieces allows you to build whatever type of system you need. Just mix and match. Naturally, HomeSaver OvalFlex is manufactured to the same .018", 4-ply certified, stainless specs that have made UL/ULC Listed RoundFlex unsurpassed in both quality and popularity. 304-alloy OvalFlex comes with HomeSaver's lifetime warranty for wood, coal, oil, and non-condensing gas applications. Read our HomeSaver warranties. HOMESAVER WARRANTIES PDF FILES OvalFlex in 304-alloy is available in 3" and 5" length, 25" coils, and custom lengths from 10" to 50". 316-alloy HomeSaver OvalFlex is available on a special order basis in lengths from 10' to 50'. OvalFlex is available in Small and Large sizes.
OvalFlex is sold in 3' and 5' lengths, 25' coils, and custom lengths from 10' to 50'. OvalFlex components (adaptors, tees, insert boots, etc.) are also available in large and small sizes. See special order by the foot OvalFlex at bottom of page. BE SURE TO READ PRODUCT AND ORDERING NOTES AT BOTTOM OF EACH PAGE.
Top/Bottom Support Brackets
O-O Adaptor: OvalFlex to OvalFlex
S-O Adaptor: Rigid Stainless to OvalFlex
Remember to use a connector-adaptor with flex pipe.
O-S Adaptor: OvalFlex to Rigid Stainless
Overall Height is 11".
OvalFlex Top Clamp and Storm Collar
Note: Top/Bottom Support Brackets can be used instead of the top clamp pictured here. Pictured on FireplaceFlex page, click here to view.
OvalFlex Tee w/Removable Take-Off & Cover
Tee Cover is sold separately.
Click here to see our custom top/bottom plates cut to your specifications.
OvalFlex Cast Iron Insert Boot
Install by drilling and bolting, or taping and screwing, into your insert top. Then seal with Furnace Cement, Flue Goo, or Flat Fiberglass Stove Gasket. Click on item name to view more information. Secure the OvalFlex into the boot with the removable rod or screws.
OvalFlex Chimney Cleaning Brush
Product Note: FL indicates freight line shipment. Ordering Note: Cut-to-length pieces of HomeSaver liner are NON RETURNABLE, so please order carefully. Ordering Note: Small OvalFlex has an inside "oval dimension" of approximately 4 1/2" x 10 3/8". Use small OvalFlex for venting stoves with 5" or 6" flue outlets. Large OvalFlex has an inside "oval dimension" of approximately 4 1/2" x 13 3/8". Use large OvalFlex for venting stoves with 7" or 8" flue outlets. For outside "oval dimensions" add 1/4" to the inside oval dimension for both Small and Large OvalFlex. Product Note: Flex pipe compresses during shipping and may need to be stretched out - instructions for stretching are included with all pipe. Product Note: All special order HomeSaver Flex pipe must ship via freight line. Carriers require packaging on all liners. This cost will be calculated after we have shipping address. TEE HEIGHT AND TAKE-OFF LENGTH FOR OVALFLEX TEES OvalFlex, With Removable Take-Off
|
HomeSaver OvalFlex was the first oval relining system
UL Listed to 1777 Standard and continues to be one of our most
poplar relining products. Now also listed to
ULC5635-00.
When joining two pieces of OvalFlex you need an adaptor
that will create a "male-end-down" connection. This adaptor
and pop rivets will do the job. And now the O-O Adaptor has
been redesigned to fit even better. 304-alloy
A
common installation is to come down the flue with rigid or flexible
stainless and attach to OvalFlex. The S-O Adaptor lets you do
this. It comes in large and small sizes. 304-alloy
Use this adaptor when joining OvalFlex that is "on top"
in an installation to a round flue collar, rigid pipe, RoundFlex, or
a rigid round tee on the bottom. 304-alloy
The 18-ga. top clamp adjusts to fit both large and small
OvalFlex. The storm collar comes in two sizes to fit large and
small OvalFlex. Use the top clamp and storm collar in
conjunction with the top plate and rain cap to finish off your
installation
properly at the top of the chimney. 304-alloy
Our newly improved OvalFlex tees have been designed for
an even better fit to OvalFlex. They come with a 5" long
removable take-off (featuring radiator-style clamps on the
inside). 304-alloy
The 18-ga. stainless top plate has outside dimensions of
either 13" x 18" or 18" x 18", and comes sized for large or small
OvalFlex. The hole is just large enough to let OvalFlex slip
through during installation and to allow for thermal
expansion. As with our RoundFlex top plates, these also have
rounded corners. 304-alloy
These boots fit over the exhaust vents of most inserts,
and OvalFlex fits snugly into the boot. 
This is simply a standard rain cap made in an oval
configuration - perfect for HomeSaver OvalFlex. 
Use this 20-ga. milled steel end-cone during OvalFlex
installations. Your helper can pull OvalFlex down past bends
much more easily with this end-cone in place. Or attach the end-cone
to the winch cable and pull the OvalFlex up the flue using our Super
Winch. When using a winch, always use care that the flex
is moving smoothly. 
These brushes are oval versions of the standard
Rutland Master Sweep Brushes with 3/8" pipe
threads.
